dupa

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - MacGyver

Pages: 1 [2]
16
Ultra Hal 7.0 / Re: New Features we would like in HAL 7.1
« on: January 22, 2018, 11:05:16 pm »
A checkbox in General Settings to enable/disable the "Are you sure you want to close Ultra Hal..."

17
Ultra Hal 7.0 / Ultra Hal Plug-in Installer Error 53
« on: December 12, 2005, 12:56:28 pm »
Good Day,
During installation of a different application (FTP Explorer app), the Ultra Hal Plug-in Installer is triggered and runs, "Installing Plugins..."; Then I get the Ultra Hal Plug-in Installer Error popup with the following:

Error 53: File not found Occured at line 8 in Ultral Hal Plug-in Installer:Form1.Form_Load

(I press IGNORE, as RETRY presents the same popup, while ABORT closes the activity)
Error 52: Bad file name or number Occured at line 9 in Ultra Hal Plug-in Installer:Form1.Form_Load

(I press IGNORE)
Error 52: Bad file name or number Occured at line 10 in Ultra Hal Plug-in Installer:Form1.Form_Load

(I press IGNORE)
Error 52: Bad file name or number Occured at line 10 in Ultra Hal Plug-in Installer:Form1.Form_Load

(I press IGNORE)
Error 52: Bad file name or number Occured at line 12 in Ultra Hal Plug-in Installer:Form1.Form_Load

(I press IGNORE)
Error 5: Invalid procedure call or argument Occured at line 12 in Ultra Hal Plug-in Installer:Form1.Form_Load

(I press IGNORE)
Error 5: Invalid procedure call or argument Occured at line 12 in Ultra Hal Plug-in Installer:Form1.Form_Load    (again)

(I press IGNORE)
Error 52: Bad file name or number Occured at line 22 in Ultra Hal Plug-in Installer:Form1.Form_Load

(I press IGNORE)
Activity closes. I'm looking back at my desktop.


So I looked in Windows (XP) Folder Options -> File Types for anuthing registered to Hal. I found 2x Haptek extensions, so I deleted them. The same senario above occurs, unchanged.

I then uninstalled Hal 6 from Control Panel->Add or Remove Programs area. The same senario above occured, unchanged.

So I rebooted (just incase). The Ultra Hal Plug-in Installer still ran (was Hal not properly uninstalled?)

Please assist... thanks!
Rick

18
Ultra Hal 7.0 / Invalid Call reading text file
« on: October 18, 2001, 04:53:38 pm »
Good day,

Using Ultra Hal Assistant v4.0.146, when I run "learn from a text file..." and select a text file (tried three: 2kb, 10kb, 7kb in size), There's always an error msgbox that pops up. The msgbox appears as it reads each line of the textfile, and is always the same.

Not sure if a file can be atached in this forum, so I'll describe the errorbox:

MsgBox title: Ultra Hal Assistant Editor
MsgBox alert is that yellow triangle with exclamation point.
and the msg is...

Error 5:
Invalid procedure call or argument
Occured at line 47
in Ultra Hal Assistant: frmLearn.Command1_Click

Buttons are Abort, Retry, Ignore.

Content of my textfiles look like this: <someword> is <the description>.

Communicating is the exchange of information.
Red zones are illegal for parking and stopping, even for only a moment.
Chocolate milk is delicious when really cold. That's why ice cream is so tasty.

Ideas?
Thanks...!
:o)
Rick

Pages: 1 [2]